Positioning 12 port patch panel is in front of the central office of information points modular device management. The front of the information point cable (Cat5e or 6 cable) into the equipment room after the first into patch panels, patch panels will hit the line modules, patch panels and switches then connect a jumper (RJ45 interface) . Overall, the patch panel is rj45 keystone jack used to manage the device, for example, if there is no patch, direct access to the front of the information points to the switch, so that once the cable problems, faced to rewiring. In addition, the management is also a bit confusing, multiple plug may cause damage to the switch port. MDF exist to solve this problem by replacing the jumper to achieve better management.
12 port patch panel Dosage and overall network is mainly based on the number of points or the floor (and similar floor, depending on how the system is designed diagram) points to the number of network configurations. Different buildings, different system designs, patch panels are the main differences between the devices. For example, a building only four rooms, the barrier terminal block master device is set on the first floor, all floors between network points are entering the device, then the patch is equal to the number of the building all network points / patch panel port number (24 mouth, 48, etc.), plus got to margin; If, on the 9th floor of a building has a room, the master device is set on the fourth floor, then in order to avoid long cable, it may partakers devices are located on each floor , and there is exchange equipment. So the main distribution frame between devices on the network is rca video cable equal to the number of points / patch panel ports (24, 48, etc.) 4 layers. Most 12 port patch panel UTP patch panels are used for horizontal wiring. The front panel assembly line equipment used to connect an RJ-45 port on the rear panel for connecting twisted-pair extending from the information outlet over. UTP patch panels are mainly 24 and 48 in two forms.
In shielded cabling system, shielded twisted pair patch panel should be selected to ensure the integrity of the shield system.
12 port patch panel
2014年4月27日星期日
2014年4月17日星期四
WISDOM 12 port patch panel How to use
What do I need a high-density patch panels network is constantly
expanding, the cable also unwittingly increase. Network Storage Rack is
usually the weak in every building room (room or with the security of
the main wiring / devices). The room area is fixed, along with the
growing number of cables, many network administrators face the crowded
cable racks and WISDOM 24 port patch panel limited room space do nothing, how can the room tidy,
well-organized layout design? 12 port patch panel is a huge problem
faced by users. The solution to this problem solution for high-density
wiring. First, from the design point of view
One thing cabling requirements do not know if you noticed not, the point is that the information requirements of data, voice, points can be exchanged when necessary, that same voice point, without changing the wiring of the situation by jumper selection Voice or data is determined. Thus, when the wiring point voice and data points are the same, 12 port patch panel design is very easy, no considered separately, the device can be unified.
If cost is not an important consideration, the receipt of all the information points rj45 patch panel, and then decide on WISDOM adsl splitter a jump by a jumper switch or voice patch panel (can be either 110 stg and other types of voice module). Of course, this is not considered a design costs, but also a thorough and voice or data terminals are considered design. Actual use is still very small. In most cases 12 port patch panel or to consider the difference between voice and data, and specific approaches there are many.
Second, from a construction point of view
Large engineering information points very much, between switching equipment and cabling systems can be connected using a jumper construction management becomes more convenient, also very clean the cabinet, after WISDOM hdmi splitter all, much shorter jumper. Detection is also a lot of convenience.
Third, management of maintenance
In fact, in this area are very concerned about the large-scale users, patch panels can effectively improve work efficiency, reduce troubleshooting time. For fast and convenient way to use it to replace the terminals provided.
One thing cabling requirements do not know if you noticed not, the point is that the information requirements of data, voice, points can be exchanged when necessary, that same voice point, without changing the wiring of the situation by jumper selection Voice or data is determined. Thus, when the wiring point voice and data points are the same, 12 port patch panel design is very easy, no considered separately, the device can be unified.
If cost is not an important consideration, the receipt of all the information points rj45 patch panel, and then decide on WISDOM adsl splitter a jump by a jumper switch or voice patch panel (can be either 110 stg and other types of voice module). Of course, this is not considered a design costs, but also a thorough and voice or data terminals are considered design. Actual use is still very small. In most cases 12 port patch panel or to consider the difference between voice and data, and specific approaches there are many.
Second, from a construction point of view
Large engineering information points very much, between switching equipment and cabling systems can be connected using a jumper construction management becomes more convenient, also very clean the cabinet, after WISDOM hdmi splitter all, much shorter jumper. Detection is also a lot of convenience.
Third, management of maintenance
In fact, in this area are very concerned about the large-scale users, patch panels can effectively improve work efficiency, reduce troubleshooting time. For fast and convenient way to use it to replace the terminals provided.
2014年4月16日星期三
12 port patch panel uses
MDF is positioned in front of the central office of information points modular device management. The front of the information point cable ( Cat5e or 6 cable ) into the equipment room after the first into patch panels, patch panels will hit the line modules , patch panels and switches then connect a jumper (RJ45 interface) . Overall , 12 port patch panel WISDOM telephone connector is used to manage the device , for example, if there is no patch , direct access to the front of the information points to the switch , so that once the cable problems, faced to rewiring. In addition, the management is also a bit confusing, multiple plug may cause damage to the switch port. MDF exist to solve this problem by replacing the jumper to achieve better management.
Dosage and overall network is mainly based on the WISDOM terminal block number of points or the floor ( and similar floor , depending on how the system is designed diagram ) points to the number of network configurations . 12 port patch panel different buildings , different system designs , patch panels are the main differences between the devices . For example, a building only four rooms , the master device is set on the first floor , all floors between network points are entering the device , then the patch is equal to the number of the building all network points / patch panel port number ( 24 mouth, 48 , etc. ) , plus got to margin ; If, on the 9th floor of a WISDOM cat5e patch panel building has a room , the master device is set on the fourth floor , then in order to avoid long cable , it may partakers devices are located on each floor , and there is exchange equipment . So the main distribution frame between devices on the network is equal to the number of points / patch panel ports ( 24 , 48 , etc. ) 4 layers.
Dosage and overall network is mainly based on the WISDOM terminal block number of points or the floor ( and similar floor , depending on how the system is designed diagram ) points to the number of network configurations . 12 port patch panel different buildings , different system designs , patch panels are the main differences between the devices . For example, a building only four rooms , the master device is set on the first floor , all floors between network points are entering the device , then the patch is equal to the number of the building all network points / patch panel port number ( 24 mouth, 48 , etc. ) , plus got to margin ; If, on the 9th floor of a WISDOM cat5e patch panel building has a room , the master device is set on the fourth floor , then in order to avoid long cable , it may partakers devices are located on each floor , and there is exchange equipment . So the main distribution frame between devices on the network is equal to the number of points / patch panel ports ( 24 , 48 , etc. ) 4 layers.
订阅：
博文 (Atom)